The Voltrix S1K (Tower) and RS1K (Rack 2U) are 1 kVA / 0.9 kW high-frequency online double-conversion (VFI) UPS systems with a built-in maintenance-free VRLA battery (2×12V/7AH). With 0 ms transfer time, input power factor correction of 0.99 at full load and a wide 60~300V (half load) 176~300V (full load) input window, they protect servers, network equipment and control systems against outages, sags, surges and frequency variation.
Both form factors share identical electrical performance; choose Tower for desktop or floor placement, or the 2U Rack model for standard 19-inch cabinets. A long-backup external-battery variant (S1KL / RS1KL) is available separately.
Technical Specifications — S1K / RS1K — 1 kVA / 0.9 kW
| INPUT | |
|---|---|
| Topology | VFI Online Dbl. Conv. |
| Input Config | 1Φ L/N+PE |
| Nominal Input V | 110~127V or 220~240V |
| Input Range | 60~300V (half load) 176~300V (full load) |
| Input Freq. | 40 ~ 70 Hz |
| Input PF | 0.99 @ Full |
| OUTPUT | |
| Output Voltage | 230 VAC (220/240/208V) or 120 VAC (100~127V) |
| Volt. Regulation | ±1% |
| Freq (Sync Mode) | 46~54 Hz 57~63 Hz |
| Freq (Bat. Mode) | 50Hz±0.05 60Hz±0.05 |
| THDv Lin./Non-lin. | 2% / 6% |
| Waveform | Pure Sine |
| Transfer Line↔Bat | 0 ms |
| Transfer Inv↔Bypass | < 4 ms |
| EFFICIENCY | |
| AC → AC | 89% |
| ECO Mode | 94% |
| Battery Mode | 87% |
| BATTERY & CHARGER | |
| Battery Type | VRLA Lead Acid |
| Battery Config. | 2×12V/7AH (internal) |
| Float Charge V | 27.3 V |
| Backup @50% Load | ≥ 5 min |
| Recharge Time | ~5 h |
| Max Rech. Current | 1.5 A |
| Display / Comm. | LED/LCD RS232/USB |
| PHYSICAL | |
| Form Factor | Tower / Rack 2U |
| Tower W×H×L (mm) | 145×220×328 |
| Rack W×H×D (mm) | 438×88×350 |
| Net Weight (kg) | 8.9 |
| ENVIRONMENT | |
| Operating Temp. | 0~+40°C |
| Humidity | 5~97% RH Non-cond. |
Key Features
- Online double-conversion (VFI) topology — 0 ms transfer, pure sine wave output
- Input power factor 0.99 at full load — reduces wiring and energy costs
- Wide input range 60~300V (half load) 176~300V (full load), 40 ~ 70 Hz — generator compatible
- Maintenance-free VRLA battery, recharge ~5 h
- AC→AC efficiency 89%, ECO mode 94%
- LED/LCD display with RS232 + USB communication
Where the S1K / RS1K Fits
The S1K and RS1K are the smallest units in the Voltrix S-Series. They are sized for a single network point rather than a whole room: a wiring closet with one edge switch and router, a small NVR, an access control panel, a point-of-sale counter or a BMS controller that must ride through short outages without rebooting. Because the topology is online double conversion, the connected load always runs from the inverter, so even a brief sag or spike never reaches the equipment.
Sizing the Load
The active power rating is 0.9 kW. The published backup figure (≥ 5 min) is given at 50% load, which for this model means about 450 W. If your equipment draws more than that, expect a shorter bridge time; if it draws less, expect longer. The internal battery is 2 × 12 V / 7 Ah, which is about 168 Wh of nominal stored energy (2 × 12 V × 7 Ah, calculated). That is enough to ride through short interruptions and to allow a clean shutdown, not to run equipment for hours.
- Add up the nameplate power (W) of every device on the UPS, then add 20–25% headroom for growth.
- Keep the total at or below 900 W; below 450 W if bridge time matters more than spare capacity.
- At full load the UPS draws roughly 4.4 A from a 230 V supply (0.9 kW ÷ 89% efficiency ÷ 0.99 input PF ÷ 230 V, calculated, excluding battery charging current). Size the supply circuit to local electrical code.
S1K, S1KL or S2K?
| Model | Active power | Battery | Max charge current | Net weight |
|---|---|---|---|---|
| S1K / RS1K | 0.9 kW | 2×12V/7AH internal | 1.5 A | 8.9 kg |
| S1KL / RS1KL | 0.9 kW | External 24V/36V | 6 A | 6.1 kg |
| S2K / RS2K | 1.8 kW | 4×12V/7AH internal | 1.5 A | 17.5 kg |
Choose the S1K when a few minutes of bridge time is enough. Choose the S1KL when the same load must run much longer from an external battery string. Move up to the S2K when the load is above about 0.9 kW or when you expect to add devices.
Installation Notes
- The tower model measures 145 × 220 × 328 mm and suits a shelf or floor position inside a closet.
- The RS1K is a 2U unit (438 × 88 × 350 mm) for a standard 19-inch rack. Check the rack depth and leave space behind the unit for airflow and cables.
- Operating temperature is 0 to +40 °C. Battery life drops when the room runs hot, so avoid unventilated cupboards.
- Use the RS232 or USB port to connect shutdown software on the protected server or NVR.
Frequently Asked Questions
Do the tower and rack versions perform the same?
Yes. The S1K and RS1K share the same electrical data; only the enclosure differs.
Can it run from a generator?
The input accepts 40–70 Hz and a wide voltage window, which helps when a standby generator starts up. Confirm generator sizing with the generator supplier.
Can I add batteries later?
No. The S1K uses its internal battery only. If longer runtime is needed, specify the S1KL / RS1KL instead.
See the full VRLA UPS range or how UPS power fits into data center infrastructure.
Ordering Information
| Voltrix Model | Form Factor | Apparent / Active Power | Battery | Part Number |
|---|---|---|---|---|
| S1K | Tower | 1 kVA / 0.9 kW | Internal VRLA (2×12V/7AH) | VTX-S1K |
| RS1K | Rack 2U | 1 kVA / 0.9 kW | Internal VRLA (2×12V/7AH) | VTX-RS1K |
Downloads
Certifications & Warranty
Designed and manufactured under ISO 9001:2015. CE (EU Declaration of Conformity), IEC/EN 62040-1 (UPS Safety), IEC/EN 62040-2 (UPS EMC — Class C2), RoHS 2011/65/EU. 2-year UPS system warranty, return-to-base, parts and labour; 1-year VRLA battery warranty. 24/7 technical support with response within 4 hours.
Specifications subject to change without notice. Backup times are indicative and depend on load, temperature, battery age and discharge history. Voltrix is a registered brand of Heizka. All trademarks are property of their respective owners.



