Overview
The Heizka Vertical Tee takes a 90° vertical drop off a horizontal run of fibre raceway, carrying patch cords down into a cabinet, frame or optical distribution frame below.
The 240 mm fitting steps a 240 × 100 mm run down to a 120 × 100 mm vertical drop, so a large backbone pathway can feed a smaller riser without an additional adaptor.
Key Features
- 90° vertical drop from a horizontal run.
- 240 mm version steps down from 240 × 100 mm to a 120 × 100 mm drop.
- Available in the 60, 120 and 240 mm series.
- Bend-radius control – the moulded profile keeps fibre patch cords within their minimum bend radius through the fitting.
- Self-extinguishing plastics – flame-retardant material to UL94-V0.
- Toolless or low-tool assembly – joins to channel and other fittings with the matching Heizka connector kits.
- High-visibility yellow – keeps the fibre pathway clearly segregated from copper services.
- Matching snap-on cover – the fitting is fully enclosed once the cover is fitted (where a cover is listed).
Technical Specifications
| Series | Item No. | Name | W (mm) | H (mm) | Overall (mm) | Colour | Material |
|---|---|---|---|---|---|---|---|
| 60 | 31140 | 60mm Vertical tee | 60 | 60 | 68 × 68 × 27 | Yellow | PVC/ABS |
| 60 | 38136 | 60mm Vertical tee cover | 60 | — | 204 × 93.5 × 7.5 | Yellow | PVC/ABS |
| 120 | 31340 | 120mm Vertical tee | 120 | 100 | 300 × 199 × 180 | Yellow | PVC/ABS |
| 240 | 36340 | 240mm to 120mm Vertical tee | 240 (W1) / 120 (W2) | 100 | 300 × 277 × 190 | Yellow | PVC/ABS |
Installation notes
- 3 connectors are needed for installation on the 120 series; the 240 series needs 2 pieces of 240 connector B kit.
- The 240 fitting steps down from a 240 mm run to a 120 mm x 100 mm vertical drop.
- Flame retardant: UL94-V0.
- Available in the 60, 120 and 240 series.
- The 60 mm cover item number (38136) was read from a scanned catalogue page at reduced confidence and should be verified with Heizka before it is treated as authoritative.
Dimensions are quoted from the Heizka Fibre Management System catalogue. Specifications are subject to change without notice – please confirm critical dimensions with Heizka before ordering.
Standards & Compliance
- Flame retardancy: UL94-V0 self-extinguishing plastics.
- Material: PVC / ABS mouldings; steel support hardware is electroplated zinc with a powder-coated finish.
- All plastic-based components are specified to be RoHS compliant.
- Colour: high-visibility yellow, identifying the fibre pathway.
- Environment: indoor use in data centres, telecommunication exchanges and equipment rooms.
Feeding a Frame or Cabinet from Above
The vertical tee is the fitting that turns part of a horizontal route straight down. It is used where an overhead fibre run must feed an optical distribution frame, a patch cabinet or a vertical riser below it, while the main run continues on. Unlike a spillout, which lets individual cords drop out, the vertical tee carries a full enclosed channel downward, so the cords stay protected and inside the system bend radius until they reach the equipment.
The 240-to-120 Step-Down Version
The 240 mm fitting (36340) takes a 240 × 100 mm run and drops a 120 × 100 mm channel. This suits the common case where a wide row trunk feeds a single frame that only needs part of its capacity. Using the step-down tee avoids a separate reducer and keeps the drop channel in the same 120 series as other branch routes, so the same 120 series channel, covers and connectors can be used below the tee.
| Item No. | Main run | Vertical drop |
|---|---|---|
| 31140 | 60 × 60 | 60 × 60 |
| 31340 | 120 × 100 | 120 × 100 |
| 36340 | 240 × 100 | 120 × 100 |
A cover is listed for the 60 mm tee (38136). For the 120 and 240 mm tees, confirm the cover requirement with Heizka when you order.
Planning Tips
- Position the tee directly above the frame or cabinet entry so the drop channel runs plumb.
- Allow for the overall size of the fitting (for example 300 × 277 × 190 mm for 36340) when checking space between the route and the ceiling or the cabinet top.
- Close any unused outlet on the run side with an end cap.
- For a branch that stays horizontal, use the horizontal tee; for a change of level on the same route, use the up/down elbows.
See the 240 series raceway or go back to the Fiber Raceway System.
Typical Applications
- Data centres and server rooms – fibre patch cord routing between racks and rows.
- Telecommunication exchanges and central offices.
- Optical distribution frames (ODF) and fibre cross-connect areas.
- Any installation where fibre must be segregated from copper services and protected end to end.
Download
Catalogue extract for this product, taken from the Heizka Fibre Management System catalogue:
Heizka Cable — Designed in the USA, distributed in 20+ countries worldwide.

